Without a refrigerator, common man’s life would be difficult to fathom.
Nearly every household in wealthy nations has a fridge.
As a result, practically everyone is aware of the issue of the refrigerator becoming out of order today.
It is vital to ascertain the causes of the refrigerator ceasing to operate and to comprehend, and how to correct the problem or how much repairs will cost the equipment, as well as to identify the primary functional components of the system.
Besides other issues of Frigidaire refrigerator compressor starts then stops problem is critical and needs to be fixed as soon as possible.
No need to worry if Frigidaire Refrigerator Compressor Starts then Stops.
This problem may be associated with compressor winding breakage, burning of motor, issues in the main control board and overheating, etc.
The detail of each cause and the fixation step is mentioned below.
Symptoms of Bad Refrigerator Compressor
The compressor facilitates refrigerant flow through the system and is the refrigerator’s beating heart.
Freon from the evaporator enters the condensing unit under pressure, cools, and transforms into liquid before returning to the evaporator with the help of the compressor.
It is required to calculate the compressor’s idle time ratio to the time the refrigerator was in use to ascertain if a malfunctioning compressor caused the refrigerator’s shutdown.
The working duration of the fridge must be divided into a complete cycle of operation to determine this coefficient.
So, for instance, if a refrigerator is turned on for 1 minute and shuts off after 15 minutes, the ratio will be 0.16, which indicates abnormal compressor operation.
However, you will most likely need to replace the compressor if the motor-compressor begins to grow hot.
Causes for Frigidaire Refrigerator Compressor Starts Then Stops
The main problems behind the abnormal behaviour of your Frigidaire refrigerator are discussed below step-wise.
Compressor winding breakage
The refrigerator cannot operate without a running compressor, which is the center of the cooling system.
The compressor’s functionality decreases with time, just like every mechanical component.
The compressor may eventually stop turning and lock mechanically.
The compressor will try to start continuously at this point, and you will notice that it is pretty hot to touch.
This problem could manifest early if the compressor has to restart often because the refrigerator is overstuffed or the coils are unclean.
The expense of replacing the compressor in the event of failure is usually excessive.
For expensive refrigerators, compressor replacement may be a more economical choice.
Inter-turn closure
The second most occurred problem behind the abnormal behavior of Frigidaire refrigerator is inter-turn closure.
Keep this problem in mind while tracing the issue of your Frigidaire refrigerator compressor that starts then stops.
Motor overheating
Another mechanical component prone to failure is the fan motor.
With time, the fan motor bearings may accumulate dirt and get clogged, rendering the motor inoperable.
If the item is readily accessible, it is often feasible to repair the refrigerator by replacing the fan motor.
Another frequent failure caused by wear and tear is dirty condenser coils.
The coils might accumulate dust and filth if they aren’t cleaned regularly.
As a result, the compressor must work harder and eventually fails because the refrigerant cannot effectively transmit heat to the air.
The issue may be readily avoided; with regular condenser coil cleaning.
Engine wedging
Engine wedging is another critical issue if your Frigidaire refrigerator starts and then stops.
Try to cater this problem at the early stage of occurrence or it could be very harmful for the life your refrigerator.
Moreover, keep the following fixation things in mind while doing this troubleshooting.
Fixes for Frigidaire Refrigerator Compressor Starts Then Stops
Make sure the problem is specifically with the compressor before purchasing a new one—which is not cheap.
You may achieve this by measuring the windings’ resistance.
Therefore, the top and bottom contact resistance should be 20 ohms in the usual condition.
If this is the case, something else is to blame for the refrigerator not working correctly.
For instance, if the hot-melt fuse or the defrosting system malfunctions, the motor compressor will not function.
Although, fixation steps are elaborated for our readers.
Replacement of Burned Contacts
Several contacts may have burnt out if the refrigerator starts up but then shuts off right away.
Most contemporary refrigerators include components that respond to changes in network voltage.
The systems can disable the refrigerator’s motor to keep it safe.
Adapting to network variations will assist the home power transformer.
The electronic control board could fail due to a network dip.
Foreign-made contemporary refrigerators often have this issue.
Trying to check and fix the problem without expert assistance will not work.
The card may only be re-flashed or replaced by a professional.
Malfunctioning of Starting Relay
If the refrigerator starts up but stalls out after a few seconds of operation, the motor starter protection relay is most likely to be at fault.
The refrigerator system’s starting relay is intended to regulate the motor and prevent overheating.
The start-up protection mechanism’s working theory is based on how metals change form when exposed to electricity.
A biometric plate, therefore, controls the refrigerator’s inclusion and de-energizing.
The motor is turned off when the plate breaks the contact due to heating caused by the current. Relay malfunctions might impact the conductivity of the plate.
As a result, the motor will start up right away after being turned on.
You may also change the relay to test if the refrigerator will function with the new pair. However, this task requires more effort.
The relay’s output may be linked to:
1.A burned-out heating spiral.
2.A jammed closure core and moveable contacts.
3.A spring bimetallic plate’s deterioration.
Replacement of Control Board
The main threat to Frigidaire refrigerator is high voltage surge, according to assessments.
A power surge’s rise in voltage leads the refrigerator to experience an inrush of electrical current.
This surge produces an excessive quantity of heat, which may harm several refrigerator components.
The control board, compressor, and ice maker are three parts that we often see damaged by a high voltage spike.
The refrigerator’s most delicate part is the control board.
As a result, it is readily destroyed when an electrical current surge generates too much heat. Due to the control board’s low cost and ease of replacement, broken control boards in refrigerators are often repairable.
Replacement of Fan Motor
Another mechanical component prone to failure is the fan motor.
With time, the fan motor bearings may accumulate dirt and get clogged, rendering the motor inoperable.
If the item is readily accessible, it is often feasible to repair the refrigerator by replacing the fan motor.
Another frequent failure caused by wear and tear is dirty condenser coils.
The coils might accumulate dust and filth if they aren’t cleaned regularly.
As a result, the compressor has to work harder and eventually fails because the refrigerant cannot effectively transmit heat to the air.
Conclusion
An essential feature of a contemporary residence is the refrigerator.
The equipment’s improper functioning may be caused by internal or external factors, such as an inadequate or excessive current flow in the power supply network.
The starting relay, motor, and control board issues are the most frequent internal issues in the refrigeration system.
The compressor and relay are DIY replacements.
However, only an expert can fix the control board and add Freon to the system, among other things.
Related Articles: